Fujitsu Irmc Default | Password
For legacy Fujitsu servers, the default username and password for the Integrated Remote Management Controller (iRMC) is admin / admin.
However, modern systems (iRMC S6 and newer) use unique credentials based on the hardware's serial number to improve security. Default Credentials by Version Default Username Default Password Legacy (S2 - S5) admin admin Modern (S6+) admin Unique Serial-Based For
and newer, the unique password is found on the physical System ID card attached to the server. Fujitsu recommends using a barcode scanner to avoid common typing errors, such as confusing the letter "I" with the number "1". How to Reset iRMC Credentials
If the default credentials fail, you can reset the password without a system reboot using IPMI tools from the host operating system.
Linux (using ipmitool):Ensure IPMI drivers are loaded, then execute:ipmitool user set password 2 .
Windows:Use the Fujitsu IPMIVIEW utility to modify user accounts directly.
BIOS / UEFI:Reboot the server, enter the BIOS (typically F2), and navigate to the Advanced -> IPMI section. You can select "Load iRMC Default Values" to return the controller to factory settings. Security Requirements for iRMC S6
When setting a new password on modern S6 systems, it must meet these criteria: At least 12 characters.
Include at least three of the following: lowercase letters, uppercase letters, digits, or special characters.
New security features include account locking after failed attempts and two-factor authentication. Troubleshooting Access If you are locked out:
The default credentials for a Fujitsu Integrated Remote Management Controller (iRMC) depend on the hardware generation of your server. Historically, Fujitsu used a universal default, but newer models (starting with ) use unique, per-device passwords for improved security Fujitsu Global Default Credentials by iRMC Generation Note: Both fields are case-sensitive. (e.g., PRIMERGY M7 series) Unique per server . You can find this password printed on the physical System ID card
(pull-out tab) located on the front of the server or on a label attached to the top cover. The password often follows the format Admin-XXXXXXX fujitsu irmc default password
and the entire string (including the prefix) must be entered. Fujitsu Global How to Find or Reset the Password Check the System ID Card:
systems, pull out the small plastic tab on the front panel. The password is listed below the barcode Use IPMITool (Local Reset):
If you have local OS access, you can reset the password without knowing the current one by using the following command in a terminal: ipmitool user set password 2 'NewPassword123!' Physical Jumper:
Older PRIMERGY motherboards often have a "password clear" or "reset" jumper near the SATA ports that can clear BIOS and management passwords. Refer to your specific model's Maintenance Manual for the exact location. Fujitsu Global IPMITool command for a different operating system, such as VMware ESXi AI responses may include mistakes. Learn more
While less publicized than Dell iDRAC or HP iLO defaults, the Fujitsu admin/admin has been cited in penetration test reports for:
| Requirement | Recommendation |
| :--- | :--- |
| Length | Minimum 12 characters |
| Complexity | Uppercase + Lowercase + Numbers + Symbols |
| Avoid | Dictionary words, season+year, company name |
| Example | Fuji$3rv3r#2024!Secure |
Do not reuse data center passwords across iRMC and other management tools.
The Fujitsu iRMC default password (admin/admin and root/fujitsu) is a necessary starting point for setting up enterprise servers. It is convenient for administrators but is also a gaping security hole if left untouched.
To summarize:
Whether you are setting up a data center, a lab, or a single server, treat your iRMC with the same security rigor as your firewall. The default is just a key—now go change the lock.
Last updated: October 2023. Firmware versions iRMC S4, S5, S6. Always refer to the official Fujitsu support documentation for your exact server model. For legacy Fujitsu servers, the default username and
You're looking for information on the default password for Fujitsu iRMC (Integrated Remote Management Controller).
The default password for Fujitsu iRMC varies depending on the model and firmware version. However, here are some common default passwords:
If these default passwords don't work, you can try the following:
To reset the iRMC password, you can try:
Security best practices:
Fujitsu Integrated Remote Management Controller (iRMC) provides out-of-band management for PRIMERGY and PRIMEQUEST servers. Access to this interface is secured by credentials that have evolved from static defaults to unique, server-specific identifiers. Default Credentials by Generation
The default username for nearly all Fujitsu iRMC generations is admin. However, the password varies significantly depending on the age of the hardware:
Legacy Systems (iRMC S2, S3, S4): Older systems often shipped with the static default password admin.
Modern Systems (iRMC S5, S6): Current servers use unique passwords to comply with modern security standards. Locating Unique Default Passwords
For modern servers, the unique password can be found in two physical locations:
System ID Card: A pull-out plastic tag on the front of the server containing a barcode and a password typically prefixed with "Admin-" followed by 12 characters (e.g., Admin-4CkNxNZqWoOK). While less publicized than Dell iDRAC or HP
Chassis Label: On smaller servers where a card is not present, a label is attached to the top cover.
💡 Key Note: The entire string, including the "Admin-" prefix, constitutes the password. It is strictly case-sensitive. Resetting or Changing the Password
If the default password fails or has been forgotten, you can reset it through several methods. Organizations can also refer to the Fujitsu PRIMERGY Security Overview for broader server hardening strategies. Using IPMITool (Local OS Access)
If you have access to the server's operating system (Linux or Windows), use the ipmitool utility to reset the admin password directly. Command: ipmitool user set password 2 .
User ID 2: This is the default ID for the "admin" user on Fujitsu hardware. Using ServerView Installation Manager (SVIM)
If the OS is unreachable, boot from the ServerView Installation Manager ISO. Open an x-term window and execute the same ipmitool command to regain access. Guidance for this and other tools is available through Fujitsu Support Downloads. Password Complexity Requirements
Starting with iRMC S6, new passwords must meet strict criteria: Minimum length of 12 characters.
Must include at least three of the following: lowercase letters, uppercase letters, digits, or special characters. Troubleshooting Common Issues
Character Confusion: Characters like capital "I" and lowercase "l" can look identical. Fujitsu recommends using a smartphone to scan the barcode on the ID card to retrieve the exact string.
"Unknown Error" at Login: On iRMC S6 (firmware 2.06S and lower), entering incorrect credentials may trigger a generic "Unknown Error" instead of a "Login Failed" message.
Manual Recovery: If you are using specialized hardware like the HyperScale appliance, you can find specific recovery steps on the Commvault Community. Peer-led technical discussions on Experts Exchange also provide legacy server support.
