Hi Sharp Dvr Reset Password New File

Once you successfully log in using a Master or Super Password, do not restart the DVR yet. The Master Password is usually temporary.

If the hardware jumper doesn't work (some Hi Sharp models solder the password to the firmware), you must re-flash the firmware. This gives you a completely new operating system and wipes the old password.

Most Hi Sharp DVR devices have a reset button located on the back or bottom of the device. Here's how to use it:

Forgetting your Hi Sharp DVR password is stressful, but it is never a permanent brick. By following the "hi sharp dvr reset password new" steps above—starting with the web portal, moving to hardware jumpers, and finally firmware flashing—you will regain access.

Always start with the simplest method: Check for a "Forgot Password" link on the login screen. If not, grab a screwdriver. Within 30 minutes, you’ll have a new password and a working security system again.

Need official support? Contact Hi Sharp’s helpdesk directly at [1-800-XXX-XXXX] or visit their official support forum. Do not trust third-party "unlock tools" from random websites—they often contain malware.

Last updated: October 2026. Methods are accurate for Hi Sharp models including HS-NVR6xxx, HS-DVR8xxx, and HS-AHD series.

To reset the password for a Hi Sharp DVR (New Model), you can typically use the built-in "Dynamic Code" feature or the official password retrieval process. If your device is brand new or recently reset, the default login credentials are usually admin / 123456.

Method 1: Using the "Dynamic Code" (Recommended for New Models)

Newer Hi Sharp models include a self-service recovery option via the local interface. Navigate to the login screen on your DVR monitor. Click on "Forget Password" or "Retrieve Password". hi sharp dvr reset password new

Select the "Dynamic Code" page to generate a unique code or QR code on the screen. Take a screenshot or photo of this dynamic code.

Send the image, along with your model number and serial number, to your regional distributor or directly to Hi Sharp Support at sales@hisharp.com.tw.

They will provide a temporary recovery code to unlock the device and set a new password. Method 2: Initial Setup & Default Credentials

If you are setting up the DVR for the first time or after a successful factory reset, use these default settings: Username: admin Password: 123456

Action: Upon first login, you will likely be prompted by a Wizard Setup to create a strong, unique password. Method 3: Hardware Reset (If Software Fails)

For models where you cannot access the software reset menu, a physical reset on the motherboard may be necessary.

Internal Reset Button: Some units have a small button on the mainboard. Press and hold it for 5–10 seconds while the unit is powered on until you hear a long beep.

Jumper Pins: If there is no button, look for two metal pins labeled "TP" or "J1". Use a screwdriver or tweezers to short-circuit these pins while powering on the device. Hold for roughly 60 seconds to restore factory defaults. FAQ - Support | HI SHARP INTELLIGENCE

If you are locked out of your Hi Sharp DVR or security system, the reset process depends on your specific model and the software version it’s running. As of April 2026, most new Hi Sharp systems utilize "dynamic codes" or QR-based recovery rather than universal master passwords. 1. Use the "Dynamic Code" Method (Newer Models)

For most modern Hi Sharp units, you can generate a temporary code through their official support channels: Once you successfully log in using a Master

Step 1: Go to the DVR's login screen and click "Forget Password" or "Retrieve Password".

Step 2: Look for a button or tab labeled "Dynamic Code". This will generate a unique code or QR code on your monitor.

Step 3: Take a photo or screenshot of this screen and send it to sales@hisharp.com.tw or your regional distributor. Include your device's model number and serial number.

Step 4: They will provide a temporary password. Once you log in, go to Settings > User to set a permanent new password immediately. 2. Common Default Passwords (Legacy Models)

If your device is older or hasn't been set up yet, try these factory defaults (Username is almost always admin): 12345 or 123456 000000 or 0000 admin Leave the password field blank. 3. Physical Hardware Reset

If software methods fail, you can perform a factory reset via the motherboard:

External Reset: Check the back or bottom for a pinhole labeled "Reset." Press and hold with a paperclip for 10–30 seconds while the device is powered on until you hear a beep.

Internal Jumper (Advanced): Power off the unit and open the case. Look for two metal pins labeled "J1" or "G1" (jumpers). Use a screwdriver or tweezers to bridge (connect) these two pins, then power the device on. Hold the bridge for 30–60 seconds to wipe the admin credentials. Troubleshooting Tips

Resetting Password of DVR/NVR by Scanning QR Code - Hik-Connect

It sounds like you’re trying to reset a forgotten password for a Hi Sharp brand DVR (digital video recorder). Last updated: October 2026

Below is a step‑by‑step guide to resetting the password on a Hi Sharp DVR without losing your recorded footage (where possible).

If the defaults failed, you are likely looking at a screen that says "Login Failed" or shows a "Hash Code." This is the most common modern security feature for Hi-Sharp units.

When you enter the wrong password multiple times, the DVR will lock you out. On many Hi-Sharp interfaces, a string of characters (numbers or letters) will appear on the screen, often labeled as a Serial Number, MAC Address, or Hash Code.

This code is the key. It is a mathematical representation of the current time or the unit's hardware ID. Because the algorithm is known, developers have created "Password Calculators" that take this code and spit out a temporary master password.

How to use this method:

Note regarding the Date: Some older Hi-Sharp algorithms rely on the system date. If the DVR has a dead CMOS battery, the date may have reset to 1970-01-01 or 2000-01-01. If your password calculator isn't working, try setting the date in the calculator to match the date shown on the DVR screen (if visible).

Some new Hi Sharp DVR models come with a QR code on the device or in the user manual. Here's how to use it:

Since Hi-Sharp DVRs often run on modified generic firmware, they are frequently compatible with popular CCTV password reset tools found on the Google Play Store or Apple App Store.

Recommended Apps: