| Control | Function | |---------|----------| | Power Rocker | Master ON/OFF | | Pressure Dial | Adjust output (70–120 PSI) | | Prime Button | Purges air before use | | LED Status (Green) | Ready | | LED Status (Yellow) | Overheat / Cooling | | LED Status (Red) | Error / Check manual |
Standard Package Includes:
Tools Required for Installation:
Suitability: Designed for sectional and up-and-over doors with a maximum width of 5 metres (for
Clearance: Requires a minimum vertical distance of 40 mm between the door and the ceiling.
Safety Space: Ensure adequate room for performing manual release and maintenance operations. 2. Installation Instructions Installation requires prior assembly of the runner parts.
Mounting: Remove the base cap and omega-shaped brackets, then secure the operator onto the runner block, ensuring the shaft is not forced.
Stops: Set the mechanical closing and opening stops against the drive carriage at the desired limits, securing them firmly. 3. Electrical Connections
Power: Uses a 230V AC 50 Hz supply with a pre-wired Schuko plug; the cable must not be altered. | Control | Function | |---------|----------| | Power
Wiring: Separate high and low-voltage cables, allowing for 40 cm of slack.
Control Unit: Must connect only to compatible Life Home Integration units. 4. Use and Programming
Operation: Pull the release cord for manual operation and re-engage by closing the door.
Remote Control: Program transmitters by pressing F1 until the LED flashes, then pressing the remote button until confirmation.
Safety: An external manual release is mandatory if the garage lacks a second entrance. 5. Maintenance
Procedures: Servicing must be done by qualified professionals.
Safety: Disconnect power during maintenance and use warning signs if necessary. Integrity: Do not modify the internal wiring.
For the full detailed documentation, you can access the Life Probo PR70 Manual PDF or view the official guide on ManualsLib. Tools Required for Installation:
Life Probo PR70 is an electromechanical operator designed for automating sectional and up-and-over garage doors. This guide summarizes the essential steps for installation, programming, and maintenance found in technical documentation from LIFE Home Integration and authorized distributors like AS-Torantriebe and Mandos ESMA . 1. Pre-Installation Checks
Door Condition: Ensure the door is mechanically sound, properly balanced, and moves smoothly without binding.
Space Requirements: The installation area must have adequate space for manual release and maintenance. For sectional doors, a minimum vertical distance of 40mm from the ceiling is required.
Alignment: The angle between the runner and the thrust arm must not exceed 30°. 2. Mechanical Installation
Mounting the Operator: Open the operator hatch, remove the base cap, and detach the omega-shaped support brackets. Insert the operator's shaft into the runner block and secure it back to the runner using the four hexagonal-headed screws.
Fixing to Ceiling: Align the runner and fasten the front and rear brackets to the ceiling using appropriate screw anchors.
Mechanical Stops: Fix the closing and opening mechanical stops on the runner to define the door's travel limits. 3. Electrical Connections & Programming
Safety First: All wiring must be performed with the power disconnected. Use the provided power cable with a ready-wired Schuko plug. Initial Setup: Despite the keyword “10 pages work
Press and hold the Start button for 5 seconds until all LEDs between '+' and '-' light up.
Press Start again; the door will automatically open and close to calibrate its stroke and find mechanical stops.
Adding Remotes: Briefly press the Blue button, press the desired button on your remote control, and press the Blue button again to confirm. Force & Sensitivity:
Adjust force levels using the Red button and '+' or '-' keys.
For obstacle detection sensitivity, hold the Red button for 5 seconds and adjust the level. How to program Probo XL
Despite the keyword “10 pages work,” the actual maintenance takes only 10 minutes per month. Follow this table:
| Interval | Task | Time | |----------|------|------| | Daily | Wipe exterior, inspect hose for cracks | 1 min | | Weekly | Clean air intake filter (tap out dust) | 2 min | | Monthly | Check all fasteners, lubricate quick-connects | 3 min | | Quarterly | Replace intake filter (Part #PR70-FILT) | 2 min | | Yearly | Internal seal inspection (authorized tech only) | 10 min |
Installation, Use, and Maintenance Manual
10-Page Working Document