Use 7-Zip to extract phison-mpall-v5.13.0c.rar:
7z x phison-mpall-v5.13.0c.rar -oC:\MPALL
While v5.13.0c is excellent for legacy drives, Newer controllers require newer tools:
| Phison Controller | Recommended MPALL Version | |------------------|----------------------------| | PS2251-50, -60 | v3.63, v3.72, or v5.13.0c | | PS2251-03, -07 | v5.13.0c, v5.15, v5.17 | | PS2251-09 (USB 3.1) | v5.21, v5.23, v6.x | | PS2251-11 (USB 3.2) | v6.0+ or STTOOL |
Other mass production tools from different vendors:
But for Phison, MPALL remains the gold standard.
Yes – unequivocally. Despite being several years old, phison-mpall-v5.13.0c.rar continues to revive legacy Phison-based USB drives that modern disk utilities cannot touch. Its stable interface, robust error recovery, and support for transitional controllers make it a permanent tool in any tech professional’s software library. phison-mpall-v5.13.0c.rar
However, it is not a “magic bullet.” Always:
If you have a bricked USB stick collecting dust, give this tool a try. You might just bring it back from the dead.
Many users arrive at this tool after their USB drive stops working normally. Common symptoms include:
| Symptom | Likely Cause | |---------|---------------| | Drive detected but 0 bytes capacity | Faulty firmware or bad block table | | Write-protected even with no physical switch | Controller locked due to failed erase | | Drive not recognized in Disk Management | Bricked after a failed format | | USB device shows as "Unknown Device" | Corrupted bootloader | | Partition cannot be deleted or formatted | Fake capacity (counterfeit) drive |
The MPALL tool can low-level format the drive, rewrite firmware, adjust VID/PID, and even restore original capacity from counterfeit drives. Use 7-Zip to extract phison-mpall-v5
Opening the software is intimidating. It looks like a throwback to Windows 98—rows of checkboxes, cryptic dropdowns like ISP, Burner, and UFD, and the ominous MP (Mass Production) button.
Using this tool is not just clicking "Next." It requires a settings.ini file or a generated config file specific to your drive's controller and NAND flash type. If you load the wrong config in v5.13.0C, you don't just lose data; you can permanently brick the controller, turning a recoverable drive into a paperweight.
This version is particularly famous for its ability to reset the BOM (Bill of Materials) ID, essentially tricking the controller into thinking it is a fresh factory unit.
After extracting the .rar file (typically 5–6 MB compressed, ~15 MB extracted), you will see:
MPALL_v5.13.0C/
├── MPALL_F1_7F00_v513_0C.exe (Main executable)
├── MPParamEdit_F1.exe (Parameter editor – critical for settings)
├── FW/ (Firmware ISP files)
│ ├── BN03V104M.BIN
│ ├── FW03FF01V10424M.BIN
│ └── ...other .BIN files
├── Setting.ini (Default tool configuration)
├── PIDVid.ini (Predefined vendor/product IDs)
└── Whitepaper.pdf (Technical notes, mostly Chinese/English)
Do not delete any folder. The tool relies on relative paths for firmware files. While v5
Not every Phison controller works with this version. Based on documentation inside the archive, v5.13.0c primarily supports:
⚠️ Caution: Do not use this version for newer controllers like PS2251-11, PS2261, or PS2305. Use newer MPALL versions (v5.16+ or v6.x) instead.
To identify your USB drive's controller, use tools like ChipGenius (Windows) or lsusb -v (Linux). Look for "Phison" and a 4-digit number starting with 22 or 2251.
If this version does not work for your drive, consider:
| Tool | Best for | |------|-----------| | MPALL v3.63.0C | PS2251-50 / 52 (older USB 2.0 drives) | | Phison ST Tool v2.07 | PS2251-01/02 for USB 3.0 recovery | | ChipEasy + phison S11 | SSD controllers (not flash drives) | | HDD Low Level Format Tool | Software-only repair (no firmware reflash) |
Do not use MPALL for Innostor or Alcor controllers – it will not work.