This is where most installations fail. The ts1162 installation manual exclusive provides a "star grounding" topology that is non-negotiable.
The Exclusive Tip: The manual includes a diagram showing a 100-ohm resistor placed between Pin 2 and chassis ground only if you experience ground loop noise. Without this exclusive diagram, technicians often short the shield to Pin 2, causing catastrophic drift.
Tecom TS1162 (also known as the 3 LED RAS) is a robust Remote Arming Station (RAS) designed for use with Challenger security systems. Rated
, it is suitable for both indoor and outdoor installations, including dusty or wet environments. Ness Corporation Mounting Instructions Disassemble the Unit
: Remove the two body retaining screws and set them aside. Pull the bottom of the body away from the base to disengage the top tabs. Prepare the Surface
: Use the mounting template to mark screw holes and the rear cable entry point. Ensure the surface is flat and vertical to prevent the base from warping when tightened. Secure the Base
: If you require rear cable entry, cut a hole in the mounting surface. Use suitable screws to mount the base assembly, ensuring the tamper lever will be fully depressed once mounted to the wall. Reassemble
: Hook the top of the body back onto the mounting tabs, swing the bottom into place, and secure it with the original retaining screws. aritech.com.au Wiring & Connectivity LAN Connection : Connect the keypad directly to the Challenger RS-485 LAN . It can be positioned up to
from the main Challenger panel or Intelligent Access Controller. Power Caution
: Ensure all power is turned off to the Challenger panel before beginning any wiring. Additional Inputs includes a specific input for Request to Exit (RTE)
control and an open collector output for controlling door relays or strikes. Ness Corporation Addressing & Configuration DIP Switches : Use DIP switches 1 through 4 to set the unique RAS address LAN Termination
: If this unit is the last device on the LAN line, set the LAN termination using DIP switch 8 aritech.com.au Safety & Maintenance Environment
: The device is rated for high-durability environments but should still have roughly 25 mm of clearance from side walls or ceilings to allow for proper mounting and accessibility.
: Avoid using water, ketones, or aromatic solvents on the keypad surface. Use a soft, dry cloth or a small amount of isopropyl alcohol if necessary. logiqit.com.au Further Exploration Tecom TS1162 3 LED RAS - Ness Corporation
Tecom TS1162 is a 3 LED Remote Arming Station (RAS) keypad used with Challenger security systems. It is specifically designed for high-durability needs, featuring an IP67 rating for dusty or wet environments. aritech.com.au Installation Highlights
While Aritech limits access to certain programming manuals to certified installers Aritech Support Portal
, the general physical installation steps for this series of RAS keypads include: support.firesecurityproducts.com.au The unit can be mounted indoors or outdoors.
Remove the body from the base by unscrewing the retaining screws at the bottom.
Use the base as a template to mark screw holes and the rear cable entry point on a flat, solid surface. Secure the base to the wall using suitable screws/bolts. Wiring and Connections : Connect the keypad directly to the Challenger RS-485 LAN
. It can be positioned up to 1.5 km away from the main panel. : The unit includes one input for Request to Exit (RTE) control and one open collector output typically used for a door relay or strike.
: All power to the Challenger panel should be turned off before wiring the RAS. Addressing
Set the unique RAS address and LAN termination using the internal DIP switches
(typically switches 1–4 for address and switch 8 for termination) before reattaching the body to the base. aritech.com.au Key Technical Specifications Environmental Rating : IP67 (Dust-tight and waterproof). Compatibility : Challenger series (Challenger10, ChallengerPlus). : Supports cabling up to 1.5 km. Ness Corporation DIP switch address table or information on how to register for the Aritech Certified Installer Portal to get the full PDF? Remote Arming Station (RAS) Keypad, 3 LED - Aritech
Remote Arming Station (RAS) Keypad, 3 LED * Robust moulded plastic housing. * Indoor or outdoor mounting. * Request to Exit input. aritech.com.au Tecom TS1162 3 LED RAS - Ness Corporation
TS1162 Installation Manual Exclusive: The Complete Pro-Grade Guide
If you’ve recently acquired the TS1162, you know it’s a high-performance piece of hardware that demands precision. Whether you are a seasoned contractor or a dedicated DIYer, this exclusive guide breaks down the installation manual into actionable steps to ensure your unit operates at peak efficiency. 1. Pre-Installation Checklist
Before unboxing, ensure your workspace is ready. Skipping this step is the leading cause of installation delays.
Verify Contents: Check that the TS1162 unit, mounting hardware, and wiring harnesses are all present.
Required Tools: You will typically need a metric socket set, a torque wrench, a multimeter for electrical testing, and high-grade silicone sealant (if applicable).
Environment: Ensure the installation area is clean, dry, and has at least 12 inches of clearance for ventilation. 2. Physical Mounting and Positioning
The TS1162 is sensitive to vibration and heat. Proper mounting is non-negotiable. ts1162 installation manual exclusive
Template Alignment: Use the provided mounting template to mark your pilot holes.
Leveling: Use a spirit level to ensure the bracket is perfectly horizontal. An uneven mount can cause internal mechanical stress over time.
Securing: Tighten the mounting bolts to the specific torque rating mentioned in the technical specs (usually around 15-20 Nm for this model). Do not over-tighten, as this can crack the housing. 3. Wiring and Electrical Integration
Disclaimer: If you are uncomfortable with electrical systems, consult a certified technician.
The TS1162 utilizes a specific three-phase wiring configuration (or standard DC, depending on your sub-model).
Grounding: Always connect the green/yellow ground wire first to prevent static buildup or surges.
Connection Points: Ensure all terminals are crimped tightly. Loose connections lead to heat, which is the #1 killer of TS1162 circuitry.
Voltage Check: Before "powering on," use your multimeter to verify that the input voltage matches the 1162’s requirements exactly. 4. Software Setup & Calibration
Modern TS1162 units often require a digital handshake upon first power-up.
Initialization: Turn the master switch on. The LED indicator should flash amber, indicating "Setup Mode."
Calibration: Follow the sequence on the interface (or via the connected app). This usually involves setting the "Zero Point" and defining operational limits.
Firmware Update: Check if there is a "Revision B" firmware update available. Installing this during the initial setup saves hours of troubleshooting later. 5. Troubleshooting Common Issues
Even with an exclusive manual, hiccups happen. Here’s the quick-fix list:
Error Code E-01: Usually indicates a polarity reversal in the wiring.
Intermittent Power: Check the fuse seated in the rear compartment; it may have loosened during shipping.
Vibration Noise: Re-check the mounting bolts; the TS1162 requires "snug-plus-quarter-turn" tension. Pro-Tip for Longevity
Schedule a "Bolt-Check" 30 days after installation. Thermal expansion can cause hardware to settle, and a quick re-torque will keep your TS1162 running silently for years.
The Tecom TS1162 is an IP67-rated, 3-LED Remote Arming Station that connects to Challenger panels via the RS-485 LAN. Installation involves RS-485 LAN termination and using separate power for distances exceeding 100 metres. For technical specifications and wiring details, see the Tecom TS1162 Datasheet. Remote Arming Station (RAS) Keypad, 3 LED - Aritech
TS1162 Installation Manual Exclusive Report
Introduction
The TS1162 is a state-of-the-art device that requires careful installation to ensure optimal performance and safety. This report provides a comprehensive guide for the exclusive installation of the TS1162, highlighting key considerations, step-by-step procedures, and essential precautions.
Pre-Installation Requirements
Before commencing the installation, ensure that:
Installation Steps
The following steps outline the installation procedure for the TS1162:
Step 1: Unpacking and Inspection (Time: 15 minutes)
Step 2: Mounting and Placement (Time: 30 minutes)
Step 3: Electrical Connections (Time: 45 minutes)
Step 4: Configuration and Testing (Time: 60 minutes)
Safety Precautions
During installation, observe the following safety precautions:
Post-Installation Checklist
After completing the installation, verify that:
Conclusion
The exclusive installation of the TS1162 requires careful attention to detail, adherence to safety guidelines, and a comprehensive understanding of the device's specifications and requirements. By following this report, installers can ensure a successful and safe installation of the TS1162.
Appendix
Revision History
Disclaimer
The information contained in this report is provided "as is" and without warranty of any kind, either express or implied. The manufacturer assumes no responsibility for any errors or omissions in this report or for any consequences arising from its use.
TS1162 Installation Manual: A Comprehensive Guide
The TS1162 is a high-performance, versatile, and reliable industrial control device designed to meet the demands of various applications. To ensure a smooth and successful installation, it's essential to follow the guidelines outlined in this article. In this comprehensive guide, we'll walk you through the TS1162 installation manual, highlighting key steps, considerations, and best practices.
Pre-Installation Checklist
Before starting the installation process, make sure you have:
Unpacking and Inspection
Carefully unpack the TS1162 device and inspect it for any damage or defects. Verify that all components, including the device, power supplies, and cables, are included and undamaged.
Mounting and Installation
The TS1162 device can be mounted in a variety of ways, including:
When mounting the device, ensure:
Electrical Connections
The TS1162 device requires careful attention to electrical connections to ensure safe and reliable operation:
Configuration and Programming
After installation, configure and program the TS1162 device according to your specific application requirements:
Post-Installation Checks
After completing the installation, perform the following checks:
Maintenance and Troubleshooting
Regular maintenance and troubleshooting are essential to ensure the TS1162 device operates reliably and efficiently:
Conclusion
The TS1162 installation manual provides a comprehensive guide for installing and configuring this versatile industrial control device. By following the guidelines outlined in this article, you'll be able to ensure a successful installation, optimal performance, and reliable operation. Remember to consult the device's manual and manufacturer's support resources for any specific questions or concerns.
Additional Resources
For more information on the TS1162 device, including detailed technical specifications, please refer to the manufacturer's website or documentation. This is where most installations fail
Connectivity: The keypad connects directly to the Challenger RS-485 LAN.
Distance: It can be installed up to 1.5 km away from the main Challenger panel or controller.
Mounting: Suitable for both indoor and outdoor environments, featuring a robust molded plastic housing.
Environmental Protection: Rated at IP67, making it resistant to dust and water exposure. Wiring & Interface
Request to Exit (RTE): Includes a dedicated input for an egress button or RTE control.
Door Control: Features an open collector output used to drive a door relay or electric door strike.
Indicators: Utilizes 3 LEDs to provide clear status feedback for system arming and access. Quick Setup Reference
If you are integrating the TS1162 into a Tecom Challenger system, remember these standard installer defaults: Default Installer Code: 4346. Installer User Number: 50.
Management Software: Compatible with Tecom C4 and Tecom Titan for advanced configuration and multisite management.
For further programming details, refer to the ChallengerPlus Programming Manual.
Tecom Titan - Default Password & Password Reset Instructions
The Tecom TS1162 is a 3-LED Remote Arming Station (RAS) designed for the Challenger security system. It is frequently used in demanding environments due to its robust construction and IP67 rating, making it suitable for dusty or wet locations. 🛠️ Core Installation Steps
Installation typically involves mounting the unit and connecting it to the Challenger RS-485 LAN.
Preparation: Ensure all power to the Challenger panel is off before beginning any wiring. Mounting:
Separate the body from the base by removing the retaining screws at the bottom.
Use the base as a template to mark mounting holes on a flat, vertical surface.
Secure the base using suitable screws, ensuring the tamper lever is properly depressed against the mounting surface. Wiring and Addressing:
LAN Connection: Connect the unit to the RS-485 LAN (up to 1.5 km from the panel).
DIP Switch Configuration: Set the unique RAS address using DIP switches 1 through 4.
Termination: If this is the last device on the LAN, set the LAN termination (DIP switch 8) to ON.
Final Assembly: Hook the top of the body onto the base tabs, swing it down, and replace the retaining screws. 📋 Key Features & Specifications
Outputs/Inputs: Includes one request-to-exit (RTE) input and one open collector output for controlling door relays or strikes.
Protection: Rated IP67 for superior weather and dust resistance.
Connectivity: Directly compatible with Challenger RS-485 LAN. Indications: Features 3 LEDs to display area status. 🔒 Accessing Official Manuals
Official technical documentation for Tecom hardware is often restricted to trained installers.
Aritech Support: You can request full installation and programming manuals via the Aritech Support Portal using professional credentials.
Replacement Parts: Items like the TS1162 Stick-on Membrane Label are available through specialized security retailers.
If you tell me what specific installation environment you're working with: Outdoor or High-dust area setup Door strike or Request-to-Exit wiring Troubleshooting a specific LED or LAN error I can provide more tailored technical advice. Remote Arming Station (RAS) Keypad, 3 LED - Aritech Remote Arming Station (RAS) Keypad, 3 LED - Aritech. aritech.com.au Tecom Manuals - Kidde Global Solutions Support
Loosen the 12 o'clock bolt just enough to slide out the 0.05mm shim. Retighten that bolt to the original thermal pre-load value. You have now achieved true zero-gap contact.
Bright Grove © 2026